The SC97VR is not a fit for the 2019 RAM 2500 and there are no backup cameras that will tie into the factory wiring on your truck. Your best bet is to install a universal backup camera that uses a different monitor than your truck's OEM screen.
I recommend going with the Rear View Safety WiFi Hitch Backup Camera System - Wireless # RVS-83112-WiFi. This system is completely wireless with a rechargeable battery and built-in WIFI connection (pre-existing WIFI is not necessary, so it works... view full answer...
The only solution for a new bracket on your Low Profile LED Combination RV Tail Light w/ Bracket - 4 Function - 8 Diodes - Round - Driver Side # RVSTL11 is total replacement. Unfortunately, a replacement bracket is not available as an individual replacement part. view full answer...
The RockyMounts MonoRail Bike Rack for 2 Bikes # RKY10004 is not rated for use on a travel trailer due to the unsophisticated suspension which will put undue stress on the bike rack and could damage it.
Instead I recommend the Swagman E-Spec Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount # S94FR. It has a per bike weight capacity of 70lbs and is rated for use on cars, vans, trucks, SUVs, travel trailers, fifth wheels, motorhomes, and flat towed vehicles. It has padded hooks... view full answer...
The Husky Center Line Weight Distribution w/ Sway Control - Trunnion - 6,000 lbs GTW, 600 lbs TW # HT32215 sounds like it needs the head angle adjusted. To relieve some tension on your bars to remove the system, I recommend using wheel chocks and then using the trailer jack to relieve some of the tongue weight. view full answer...
The best solution for a weight distribution system will be one with a better range to fit what your trailer would have. For that I would recommend the Reese Strait Line part # RP66084 which has as tongue weight range of 600-1,200 lbs which will work great for you but also because it has the best and only sway control out there that will work to fight sway before it starts.
For a 2 inch ball you would want part # A-90 and for a 2-5/16 inch ball # 19286. view full answer...
The Cup Holder for Thomas Payne Momentum Recliners and Sofas - Qty 1 Item # 195-387597 were designed to be extra sensitive so that you can easily use them by just gliding your finger over them and there unfortunately is no way to turn the sensitivity on them down. view full answer...
The Jr Products RV LED Light Side-Slide Dimmer Switch - Black item # 37205-12315 has 2 mounting holes on the back of the unit. The front cover is removable to access them for installation. I have attached a picture of the back side of the dimmer switch. view full answer...
If the height of the I-beams is less than 6" as you say then you would have to have to swap out the regular safety struts for the Mount-n-Lock SafetyStruts Universal RV Bumper Support Brackets # MO34VR, which include spacers to place the brackets far enough out to clear the flange lip. You would not want to trim the flange of your trailer frame beams.
You can place the supports on the inside or the outside of the frame beams as the difference between the two sides really isn't going to... view full answer...
Yes, since the jaws are what will be holding the items they will be able to handle 15 lbs of weight.
The Quick Fist Mini Clamps # QF30050 are rated for 25 lbs each so 15 lbs will not be a problem at all. view full answer...
The Stromberg Carlson Bike Bunk Trailer-Mounted Bike Rack Carrier for A-Frame Trailers - 2"-100lbs Item # CC-275 has a max weight capacity of 100lbs so it wouldn't be able to support the bike rack and 4 bikes.
Instead you can install a Curt Adjustable Trailer Hitch Receiver - 18"-51" Wide - 2" Drop - Class III - 2" Item # C13701 if your frame distance falls between 18-51", if not let me know and we can find an alternative.
Once you have the hitch installed you can insert the Swagman... view full answer...
The install of the Lippert Components High-Speed Power Stabilizer Jack # LC298707 that you referenced is not overly difficult. If you have basic mechanical skills and tools this wouldn't be a problem for you at all. I attached an install video link to this page for you to check out as well to see what the process is and to use as a step by step guide for when you're ready to install the kit.
This is sold as a set that would have a left and right leg that would lower and stabilize to the ground. view full answer...
All of the cables and connectors to connect the:
-Go Power DuraLite Portable Solar Panel Expansion # GP76FR are included in the kit.
This kit includes quick connectors, ring terminals, a digital solar controller, battery clamps, XLR-Style solar plug, and a canvas kit bag.
This kit will work most portable power stations, and will also work with pre-wired Furrion solar setups as well.
Additionally, since it uses its own 30 amp controller it won't be able to be tied into your existing... view full answer...
We do indeed offer ST205/15-14 radial tires from 5 different manufacturers in load range B(1430 lbs), C (1760 lbs) and D (2040 lbs).
If you want the best tire available that's manufactured in the USA, I'd recommend the Goodyear Endurance, part # 724864519 this is a D rated radial tire with a 2040 lb capacity per tire or 4080 lb per axle.
For something a bit less expensive, you could go for the Westlake # 274-000012, which is also a radial and has the same weight rating. view full answer...
The MaxxAir UniMaxx Universal Replacement Lid for RV and Trailer Roof Vent - Translucent White # MA00-335001 you were looking at will indeed fit the roof vent of your 2018 Forest River Flagstaff Micro Light Travel Trailer as it is designed to fit all roof vents. This is possible due to the universal mount that is included that screws into the vent itself.
Since you mentioned your roof vent your roof vent has a 3 point hinge then another possible option is the Replacement Lid for Jensen... view full answer...
The Lippert stabilizer jack part # LC298707 does fit your 2021 Flagstaff 25FKS and will go a great job replacing your scissor jacks. This will be much easier than manually cranking scissor jacks. The mounting holes are not going to match up though so you would have to drill new ones or have this welded on. view full answer...
We've asked Solera in the past about how much clearance above the slide out would be needed for a slide topper to fit and they have said in past that between 3 and 6 inches would be fine so your clearance of 4-3/4 inches would be more than adequate.
I attached a link to the install instructions to this page but even more helpful is I attached a link to an install video that will walk you through the entire process. view full answer...
The Adco Olefin HD RV Cover for Travel Trailers up to 20' - All Climate + Wind - Gray # AD97ZR has a 3-year warranty and fits trailers between 22" and 24' long. If you measure the length of your Micro-Lite and take into consideration the rear ladder and it's not longer than 24' the cover will work well for you.
Please let me know if it ends up being longer than 24' and we I can make additional recommendations. view full answer...
The Compartment Door Key Lock - 5/8" - Standard Item # 372305 uses a universal key (751 style) so if you have the 751 style on your other locks you'll be able to use the same key on all locks. view full answer...
Thank you for all of the info you listed from your current hub seals. Based on that the correct seal kit would be the Grease Seal part # RG06-050. view full answer...
Screen door latches are pretty much universal so you really just need to ensure that you're selecting the correct direction, but no manufacturer follows the same point of view when labeling their directions so the key is to look at the plunger.
If you're standing outside of your trailer looking in and your handle needs to be on the left then you'll want the Door Latch for Amerimax RV Screen Doors - Right Hand # 37210765.
If you're standing outside of your trailer looking in and your... view full answer...
Go To Results